|
08:00
Doors open & coffee
|
|
09:00
Conference opening by Prof. dr. ir. Roeland De Breuker
|
09:10
Keynote Christos Kasapoglou (TU Delft/Lockheed Martin)
Chair: Daniël Peeters
09:10
40 mins
|
The disconnect(s) between materials, manufacturing technologies and designers’ needs: Transforming the Aerospace Engineer’s challenges into opportunities
Christos Kassapoglou
|
|
09:50
Session 1: Technologies for Additive Manufacturing
Chair: Daniël Peeters
09:50
20 mins
|
Photogrammetry in Large Format Additive Manufacturing: an alternative tool for machining setup and inspection
Pedro Andre Garcia Camino, Lucas Abia Hof, Simon Joncas
|
10:10
20 mins
|
Cost-effective large scale 3D printing of continuous fibre-reinforced thermoplastic composites using UD tapes
Erik Kramer, Menno Jan Rietema, Bert Weteringe
|
|
|
10:30
BREAK
|
11:00
Session 2: Trajectories for Automated Fiber Placement
Chair: Brian Tatting
11:00
20 mins
|
Fibre Path Planning for Automated Fibre Placement on Doubly Curved Structures
Avyadhish Malladi, Christos Kassapoglou, Daniël Peeters
|
11:20
20 mins
|
Layup Strategies for in-situ Automated Fiber Placement of Complex Geometries
Lukas Raps, Ashley Chadwick, Heinz Voggenreiter
|
11:40
20 mins
|
Rule-based app tape path design for aerospace composite structures a geometry-classified manufaturability assessment
Julian Schuster, Maximilian Holland
|
12:00
20 mins
|
Continuous Trajectory Generation for the Automated Manufacturing of Super-Ellipsoidal Composite Pressure Vessels
Gregorio Ferreira, Shahrzad Daghighi, Giovanni Zucco, Paul Weaver
|
|
|
12:20
LUNCH
|
14:00
Session 3: Thermoplastic Tapes
Chair: Bariș Çağlar
14:00
20 mins
|
Relevance of deconsolidation on the porosity of thermoplastic cfrp tubes wound with direct electrical resistance heating
Jonas von Heusinger, Jonas Naumann, Yannis Grohmann, Mihai Fetecau, Daniel Stefaniak, Clemens Dransfeld
|
14:20
20 mins
|
A Quantified Comparison of Commercial CF-LMPAEK Tapes
Ashley Chadwick, Yannick Schäfer, Clara Thaldorf, Stefan Fliescher
|
14:40
20 mins
|
Flax to the Future: Processing–Structure Relationships in Continuous Natural Fiber Thermoplastic Tapes
Dimitrios Apostolidis
|
15:00
20 mins
|
Pulsed Flashlamp (HUMM3) Heating of Thermoplastic Composite Tape in In-Situ Automated Fiber Placement: Thermal Response and Physical Changes
Kasahun Niguse Asfew, Julie Teuwen, Daniël Peeters
|
|
|
15:20
BREAK
|
15:50
Session 4: Manufacturing Simulation
Chair: François-Xavier Irisarri
15:50
20 mins
|
Is laser cutting a suitable alternative for cutting carbon fibre preforms?
Dominic Stratton
|
16:10
20 mins
|
Composite Thermoforming Defect Identity Cards: Cause, Prevention, Detection, Significance, and Progression
Matthew Godbold, Ben Francis, Ramy Harik
|
16:30
20 mins
|
Effects of curing-induced residual stresses in filament-wound composite pressure vessels under cryogenic temperatures
Ivan Komala, Julien van Campen, Daniël Peeters, Morteza Abouhamzeh, Sebastian Heimbs
|
|
|
17:10
ACM8 pitch
|
|
17:40
Transportation to CEAD for the Welcome Reception
|